• PE-hose in high quality
• LD-Polyethylene - light, with high stability
• resistant against many chemicals
• For the assembly of capillaries & micro tubes
• quantity in shopping cart = length in meters

You can use these PE pipes for your grow. No matter if indoor or outdoor, the used low density polyethylene (LDPE PN4) is very resistant against weather conditions and most of the chemicals used in cultivation. With diameters of 16 - 25 mm, PE hoses are perfect for main / supply lines for automatic drip irrigation. Due to the high quality of the material, it is also possible to install iDrop single drip irrigators or cappilaries directly on the hose.

• PE-hose in high quality
• LD-Polyethylene - light, with high stability
• resistant against many chemicals
• For the assembly of capillaries & micro tubes
• quantity in shopping cart = length in meters

You can use these PE pipes for your grow. No matter if indoor or outdoor, the used low density polyethylene (LDPE PN4) is very resistant against weather conditions and most of the chemicals used in cultivation. With diameters of 16 - 25 mm, PE hoses are perfect for main / supply lines for automatic drip irrigation. Due to the high quality of the material, it is also possible to install iDrop single drip irrigators or cappilaries directly on the hose.

• PE-hose in high quality
• LD-Polyethylene - light, with high stability
• resistant against many chemicals
• For the assembly of capillaries & micro tubes
• quantity in shopping cart = length in meters

You can use these PE pipes for your grow. No matter if indoor or outdoor, the used low density polyethylene (LDPE PN4) is very resistant against weather conditions and most of the chemicals used in cultivation. With diameters of 16 - 25 mm, PE hoses are perfect for main / supply lines for automatic drip irrigation. Due to the high quality of the material, it is also possible to install iDrop single drip irrigators or cappilaries directly on the hose.

• PE-hose in high quality
• LD-Polyethylene - light, with high stability
• resistant against many chemicals
• For the assembly of capillaries & micro tubes

You can use these PE pipes for your grow. No matter if indoor or outdoor, the used low density polyethylene (LDPE PN4) is very resistant against weather conditions and most of the chemicals used in cultivation. With diameters of 16 - 25 mm, PE hoses are perfect for main / supply lines for automatic drip irrigation. Due to the high quality of the material, it is also possible to install iDrop single drip irrigators or cappilaries directly on the hose.

Plant care without a power supply or any additional devices with the easy2grow self-watering system The 47-litre tank only has to be filled with water and any additional ingredients of your choice every few weeks, and enables the creation of a water flow using its own pressure. The patented AQUAvalve therefore gives plants the ability to independently control the supply, which ensures the optimal wet-dry cycle and is a good imitation of nature. In short, you can say that the system runs itself and you don?t need many devices or any power at all in order to achieve the best results. The system (2 pots) can be used for all kinds of greenhouse plants and can be expanded to up to 6 pots. The extension kits are connected using the tee pieces included. If 6 pots aren?t enough for you, you can also combine several 47 litre tanks and pots.

Fits with every AutoPot system that works with 16mm or 9mm pipe

Fits with every AutoPot system that works with 16mm or 9mm pipe

Replacement Pot for Easy2Grow and 1Pot Modules

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This Set Contains

• made of robust and high-quality plastic
• for 8,5l and 15l pots

AutoPot easy2grow coaster for 2 pots. The coaster fits 8.5 liter pots as well as 15 liter pots. Also the pots of the AutoPot 1Pot system fit into this coaster.

• to cover the AQUAvalve in the easy2grow coaster

AQUAvalve cover for easy2grow coasters. The cover only fits in the easy2grow coaster for two 8,5L or 15L pots.

Spray bottles are a useful aid in a grow room. A pump spray bottle can be used to apply nutrients directly to the leaves. The absorption of fertilisers via the leaves gives the plant direct access to the nutrients, which means that they do not have to be transported through the entire plant.

The AutoPot 100 litres FlexiTank revolutionises water storage, it is everything you need in one compact box.

The AutoPot 225 litres FlexiTank revolutionises water storage, it is everything you need in one compact box.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

• easy to transport
• very robust with specially sealed seams
• superfast assembly
• space saving during storage

The Autopot FlexiTank is a revolution in water storage. You can assemble and disassemble it quickly and easily. It can be used both indoors and outdoors and has a capacity of up to 750 liters. The installation takes only a few minutes and you do not need any tools. The tank is foldable and can be stored very space-savingly when not in use. The transport of bulky water tanks is now a thing of the past. The Autopot FlexiTank is robust and has specially sealed seams. A sophisticated finish guarantees that it is 100 percent waterproof. Each FlexiTank has a tap connection and an overflow.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

Never water your plants again! The ECO self-watering system is as practical as it is affordable, and is the perfect accessory for installing a drip irrigation system for up to 4 plants quickly and easily!

Never water your plants again! The ECO self-watering system is as practical as it is affordable, and is the perfect accessory for installing a drip irrigation system for up to 8 plants quickly and easily!

Never water your plants again! The ECO self-watering system is as practical as it is affordable, and is the perfect accessory for installing a drip irrigation system for up to 12 plants quickly and easily!

Never water your plants again! The ECO self-watering system is as practical as it is affordable, and is the perfect accessory for installing a drip irrigation system for up to 16 plants quickly and easily!

Never water your plants again! The ECO self-watering system is as practical as it is affordable, and is the perfect accessory for installing a drip irrigation system for up to 20 plants quickly and easily!

Never water your plants again! The ECO self-watering system is as practical as it is affordable, and is the perfect accessory for installing a drip irrigation system for up to 24 plants quickly and easily!

Never water your plants again! The ECO self-watering system is as practical as it is affordable, and is the perfect accessory for installing a drip irrigation system for up to 36 plants quickly and easily!

Never water your plants again! The ECO self-watering system is as practical as it is affordable, and is the perfect accessory for installing a drip irrigation system for up to 40 plants quickly and easily!

• for enriching the nutrient solution with oxygen
• for better growth and higher yields

You can use this bubble stone to distribute air from an air pump in the nutrient solution or water of your Indoor Growing. The fine air bubbles dissolve considerably more oxygen in the water than if only the air hose is led into the water tank. A higher proportion of dissolved oxygen in the nutrient solution increases the ability of the roots to absorb nutrients. Harmful bacteria also find it more difficult to multiply in water with a high oxygen concentration.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

• Pumping volume: 3,500 litres per hour
• Discharge height: 5.5 meters
• for use in irrigation systems

This submersible pump from Remmer is well suited for use in complex irrigation systems. It offers you a pump capacity of 3,500 litres per hour and a delivery head of 5.50 m. It is therefore also suitable for use in deep water tanks or even rainwater barrels.

This heating rod is ideal for tempering nutrient solutions because it is insulated and water-repellent. With the integrated temperature controller, the temperature of 18-34°C can be set precisely. Thanks to the thermostat, you can reach and keep a constant temperature.

Friends of more complex or improvised grow setups surely know the problem of managing the different temperatures that are crucial to healthy plant growth. Whilst the air temperature can often be well controlled using ventilation, it can often be a lot more difficult when it comes to nutrient solution tanks.

Friends of more complex or improvised grow setups surely know the problem of managing the different temperatures that are crucial to healthy plant growth. Whilst the air temperature can often be well controlled using ventilation, it can often be a lot more difficult when it comes to nutrient solution tanks.

• for constant temperature control of nutrient solutions
• insulated and water-repellent
• precise adjustment between 18 and 34 °C
• ensures optimal nutrient absorption

This heating element is ideal for the temperature control of nutrient solutions, because it is insulated and water-repellent. With the integrated temperature controller, the temperature can be set accurately from 18-34 °C. Thanks to the thermostat a constant temperature is achieved. This heating rod has a power of 500 Watt and is therefore suitable for nutrient solutions up to 500 litres. We also offer variants with 100, 200 and 300 Watt, which are suitable for correspondingly smaller nutrient reservoirs. The use of a heating rod has proven itself in aquaristics, where a constant water temperature is also of great importance. This allows nutrient solutions to be kept at a constant temperature to ensure optimal nutrient uptake.

• for micro irrigation systems
• 12 droppers
• 2.3 l/h per dropper

The Maverick Water Spider is an extremely practical tool for your automatic irrigation system. It simplifies the water and nutrient supply of your plants during indoor growing - twelve plants can be watered at the same time. With the practical and robust 25 mm connections you can either loop the spider directly into 25 mm PE pipes or mount it as an end piece. Each dropper delivers 2.3 liters of liquid per hour. Due to the large diameter of the capillary tubes, there are hardly any blockages, even most organic fertilizers can be used.

The Nutriculture Maxi Jet Pump is a fully Submersible multi-use pump. It offers high performance and low power consumption. This versatile pump can be used externally or submerged.

The Nutriculture Maxi Jet Pump is a fully Submersible multi-use pump. It offers high performance and low power consumption. This versatile pump can be used externally or submerged.

The Nutriculture Maxi Jet Pump is a fully Submersible multi-use pump. It offers high performance and low power consumption. This versatile pump can be used externally or submerged.

The compact, reliable pump with adjustable flow rate. Includes air infuser perfect for aerating nutrient solution.

The compact, reliable pump with adjustable flow rate. Includes air infuser perfect for aerating nutrient solution.

• removes up to 99% of chlorine and dirt particles
• easy to exchange

As far as the use of the filters is concerned, Growmax has designed the various systems in a very practical and thoughtful way. Whether it is a pure water filter or a high quality reverse osmosis filter, this filter element fits into several installations. The filter element should be changed every 4-6 months for the reverse osmosis plants, for the Eco Grow 240 l/h after approx. 11000 litres.

• for high and low pressure
• with 1/4 " and 3/8 " pipe connectors

If you want to fill your water tanks unattended, you can mount this float switch directly on the tank. The float valve set is supplied with pipe connectors for 1/4 inch and 3/8 inch. With this high performance float valve, you can ensure that your indoor grow does not overflow your irrigation system's tank.

• 2-stage filter system
• removes up to 99 % of chlorine and pollutants
• simple and currentless installation
• Filter elements quickly changeable

Ordinary tap water often contains chlorine and other undesirable substances. Even if pollutants such as herbicides, pesticides, PCBs, benzene, etc. are only present in small quantities, they accumulate in the growing medium and your plants over time. With the GrowMax Pro Grow water filter you remove up to 99% of these pollutants and sediments down to a size of 5 microns. You will have up to 2000 litres of high quality purified water per hour at your disposal.

• Spare membrane for Power Grow 500, Mega Grow 1000 & Maxquarium
• easy to assemble

This reverse osmosis replacement membrane is suitable for different Growmax systems. In the Power Grow 500 l/h you need one membrane, in the Mega Grow 1000 l/h and the Maxquarium two each. When the old membrane(s) have reached their wear limit, you can easily and cheaply replace them. The change is similar to the change of the pre-filter.

• removes up to 99% of chlorine and dirt particles
• easy to exchange

The filters of your Super Pro Grow 800 filter system should be changed after approx. 56000 litres. The set contains a coconut fibre carbon filter and a 5 micron sediment filter element.

Technical details:

• removes up to 99% of chlorine and dirt particles
• easy to exchange

The filters of your Garden Grow 480 filter system should be changed after approx. 27000 litres. The set contains a coconut fibre carbon filter and a 5 micron sediment filter element.

Technical details:

• replacement filter of the deionisation stage
• easy replacement with screw housing
• Filter for maximum water purity

The filters of your Maxquarium 000 PPM filter system should be changed approximately every 4-6 months. This also applies to the deionisation filter. It increases the filter function of the reverse osmosis system from 95% to almost 100% and should therefore be changed regularly. This way you maintain the efficiency of your system and always have the purest water available for your grow.

• 2-stage filter system
• removes up to 99% of chlorine and pollutants;
• simple and currentless installation
• Filter elements quickly changeable

Ordinary tap water often contains chlorine and other undesirable substances. Even if pollutants such as herbicides, pesticides, PCBs, benzene, etc. are only present in small quantities, they accumulate in the growing medium and your plants over time. With the GrowMax Super Grow water filter you remove up to 99% of these pollutants and sediments down to a size of 5 microns. You will have up to 800 litres of high quality purified water per hour at your disposal

• 2-stage filter system
• removes up to 99 % of chlorine and pollutants
• simple and currentless installation
• Filter elements quickly changeable

Ordinary tap water often contains chlorine and other undesirable substances. Even if pollutants such as herbicides, pesticides, PCBs, benzene, etc. are only present in small quantities, they accumulate in the growing medium and your plants over time. With the GrowMax Eco Grow water filter you remove up to 99% of these pollutants and sediments down to a size of 5 microns. You will have up to 240 litres of high quality purified water per hour at your disposal.

• removes up to 99% of chlorine and dirt particles
• easy to exchange

The filters of your Super Grow 800 filter system should be changed after about 27000 litres. The set contains a coconut fibre carbon filter and a 5 micron sediment filter element.

Technical details:

• 2-stage filter system
• removes up to 99 % of chlorine and pollutants
• simple and currentless installation
• Filter elements quickly changeable

Ordinary tap water often contains chlorine and other undesirable substances. Even if pollutants such as herbicides, pesticides, PCBs, benzene, etc. are only present in small quantities, they accumulate in the growing medium and your plants over time. With the GrowMax Garden Grow water filter you can remove up to 99% of these pollutants and sediments up to a size of 5 micrometers.

• maximum water purity
• removes up to 100% of salts and pollutants
• up to 500 litres of purest water per day
• removes 99 % of chlorine and sediment

The Maxquarium 000 PPM reverse osmosis system produces extremely clean water for watering your indoor grow. The Growmax system works with a combination of filters and pressure, thus eliminating virtually all salts and heavy metals from tap water. In addition to the reverse osmosis membranes also used in the other systems, a deionisation filter is also used here. The osmosis water filtered in this way not only protects the natural microorganisms in the soil. It also has an ideal pH value of 6.5 and a significantly reduced EC value of < 0.1. The nutrient uptake of the plants can therefore be controlled much better and more precisely.

• powerful reverse osmosis filter
• removes 95 % of salts and heavy metals
• up to 1000 litres of pure water per day
• enables the exact setting of the EC value

The reverse osmosis unit Growmax Water Mega Grow 1000 is your strong partner for the production of pure irrigation water for hydro systems and the cultivation on all known media at indoor growers. The Growmax system works with a combination of filters and pressure and in this way eliminates almost all salts and heavy metals from tap water. The osmosis water filtered in this way not only protects the natural microorganisms in the soil. It also has an ideal pH value of 6.5 and a significantly reduced EC value of < 0.1. The nutrient uptake of the plants can therefore be controlled much better and more precisely.

• for sealing threaded connections

If you need to seal threads, simply use this Teflon tape. Unlike many liquid thread sealants, you can easily undo this connection later if needed.

• robust material
• for connecting 2 fittings with male thread
• with built-in seal
• reusable

If you want to connect hoses or PE pipes ending on fittings with 3/4 inch male thread, this coupling offers the perfect solution. A rubber seal is directly inserted into the robust PE housing. So you don't need any further sealant like Teflon tape or similar. It won't become any easier and safer than this!

• robust positioning spring design
• flow rate 50 - 1000 l/h
• fixed outlet pressure of 1,1 bar
• easy assembly due to thread

With this pressure reducer you can safely reduce line pressures from a maximum of 8 bar to exactly 1.1 bar. The pressure reducer is equipped with a diaphragm and adjusting spring, which guarantees a permanent reliable operation. Regardless of the inlet pressure or the flow rate, it stably maintains a fixed preset outlet pressure of 1.1 bar.

• robust positioning spring design
• flow rate 50 - 1000 l/h
• fixed outlet pressure of 2,5 bar
• easy assembly due to thread

With this pressure reducer you can safely reduce line pressures from a maximum of 8 bar to exactly 2.5 bar. The pressure reducer is equipped with a diaphragm and adjusting spring, which guarantees a permanent reliable operation. Regardless of the inlet pressure or the flow rate, it stably maintains a fixed preset outlet pressure of 2.5 bar.

• earth spike for placing the drip tubes
• for micro-irrigation

If you use nozzle distributors in your irrigation system, you can use the drip tube holder to determine the exact position of the individual drippers / drip tubes. Simply insert it into the ground and hang the drip hose.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

• micro dropper with large pressure range
• flow rate adjustable

This micro dropper fits on 4 x 6 mm micro tubes and you can set a flow rate of 0 - 6 l/h The pressure range is from 0.5 - 5 bar.

• stainless steel spring
• solid brass housing
• prevents backflow of casting water
• safe mounting due to thread

If you use an irrigation system for your grow, you should use a check valve. For example, if there is negative pressure in the domestic water system and your irrigation system is connected to it, the non-return valve prevents contamination of the drinking water. The built-in NBR membrane and the stainless steel spring are extremely durable and can withstand temperatures of up to 100°.

• Connector for nozzle distributors and PVC / PE - pipe

If you work with drip irrigation in your indoor or outdoor grow and want to use nozzle manifolds, you need this mounting ring to connect the nozzle manifolds safely and tightly to the supply line.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

• robust connection fitting
• connects external thread with hose coupling

If you are looking for an easy way to quickly connect hoses to a tap, you can easily do this with the Gardena tap piece. Your tap only needs to have a 3/4" external thread. The coupling part fits all standard couplings of this size.

• robust coupling from Gardena
• with built-in water stop

With this coupling you can connect a water hose of your irrigation system with 13 mm or 1/2 " to a tap piece. The big advantage, especially for indoor growing, is the integrated water stop. This prevents water from running out of the hose at this end after disconnecting the connection when you roll it up or transport it.

• micro dropper with large pressure range
• flow rate adjustable
• with earth spike for direct fixing in the pot

This micro dropper fits on 4 x 6 mm micro tubes and you can set a flow rate of 0 - 6 l/h The pressure range is from 0.5 - 5 bar. With the practical earth spike it can be easily placed and aligned in pots or in the ground.

• Fixing for hoses with 5 - 6 mm outer diameter
• Simply pluggable into earth / substrate
• Fits perfectly for 4x6mm micro tube

With this holder you can fix the micro tubes in your droplet irrigation system quickly and easily. Simply insert the soil spike into the ground at the appropriate place and clamp the micro tube into the opening at the top.

• free from cadmium and lead
• flexible PVC type 200
• Production with natural raw materials

This micro hose is manufactured under the highest standards of quality and freedom from pollutants. So you can use it without hesitation for the micro irrigation of your indoor or outdoor grow. Only natural raw materials are used in the production. Therefore, a contamination with heavy metals such as lead or cadmium can be excluded. Due to the flexibility of PVC you can lay this micro hose very easily.

• free from cadmium and lead
• flexible PVC type 200
• Production with natural raw materials

This micro hose is manufactured under the highest standards of quality and freedom from pollutants. So you can use it without hesitation for the micro irrigation of your indoor or outdoor grow. Only natural raw materials are used in the production. Therefore, a contamination with heavy metals such as lead or cadmium can be excluded. Due to the flexibility of PVC you can lay this micro hose very easily.

• free from cadmium and lead
• flexible PVC type 200
• Production with natural raw materials

This micro hose is manufactured under the highest standards of quality and freedom from pollutants. So you can use it without hesitation for the micro irrigation of your indoor or outdoor grow. Only natural raw materials are used in the production. Therefore, a contamination with heavy metals such as lead or cadmium can be excluded. Due to the flexibility of PVC you can lay this micro hose very easily.

• capacity: 0-40 l/h adjustable
• spray radius: 0-0,38m adjustable
• Optimum water pressure 1 Bar
• 180° spray angle

With this jet nozzle you can irrigate slightly larger areas for your indoor or outdoor grow than with a dripper. The 180° orientation allows you to reach the desired areas very precisely. With the ground spike you can quickly mount the nozzle and easily align it.

• Connector for 3/4" inch thread and micro tube
• for use in micro irrigation

If you want to connect the micro-tube part of your drip irrigation system to a pipe that ends with a 3/4" male thread, you can quickly and easily create a tight connection with the micro-adapter.

• Connector for two 16mm PE pipes of equal thickness
• fast and easy assembly

With this screw coupling you can easily and safely connect two PE pipes with a diameter of 16 mm each. You can open the screw connection at any time and continue to use the coupling for watering your groves.

• Connector for two 20mm PE pipes of equal thickness
• fast and easy assembly

With this screw coupling you can easily and safely connect two PE pipes with a diameter of 20 mm each. You can open the screw connection at any time and continue to use the coupling for watering your groves.

• Connector for 2 25mm PE pipes
• fast and easy assembly

With this screw coupling you can easily and safely connect two PE pipes with a diameter of 25 mm each. You can open the screw connection at any time and continue to use the coupling for watering your groves.

• Fitting for connecting different pipe sizes

With this reduction coupling you can create a watertight and above all stable connection between PE pipes with a diameter of 20 mm and PE pipes with 16 mm. The coupling is screwable and can be unscrewed and reused if necessary.

• Fitting for connecting different pipe sizes

With this reduction coupling you can create a watertight and above all stable connection between PE pipes with a diameter of 25 mm and PE pipes with 20 mm. The coupling is screwable and can be unscrewed and reused if necessary.

• practical connector for 20 mm PE pipe on 1/2" thread
• robust and reusable
• for 1/2 inch external thread

With this connection fitting you can connect a 20 mm PE pipe to a water tap or pipe with 3/4 inch male thread connection. Since there is also a screw connection on the side of the PE pipe, you can loosen the screw connection again if necessary and use it for further drip irrigation concepts.

• practical connector for 20 mm PE pipe on 3/4" thread
• robust and reusable
• for 3/4 inch external thread

With this connection fitting you can connect a 20 mm PE pipe to a water tap or pipe with 3/4 inch male thread connection. Since there is also a screw connection on the side of the PE pipe, you can loosen the screw connection again if necessary and use it for further drip irrigation concepts.

• Connector for 16 mm PE hose on 1/2 " thread
• robust and reusable
• with 1/2 inch external thread

With this connection fitting you can connect a 16 mm PE pipe with a hose or pipe with 1/2 inch female thread connection. Since there is also a screw connection on the side of the PE pipe, you can loosen the screw connection again if necessary and use it for further drip irrigation concepts.

• Connector for 16 mm PE hose on 3/4 " thread
• robust and reusable
• with 3/4 inch external thread

With this connection fitting you can connect a 16 mm PE pipe with a hose or pipe with 3/4 inch female thread connection. Since there is also a screw connection on the side of the PE pipe, you can loosen the screw connection again if necessary and use it for further drip irrigation concepts.

• Connector for 20 mm PE hose on 3/4 " thread
• robust and reusable
• with 3/4 inch external thread

With this connection fitting you can connect a 20 mm PE pipe with a hose or pipe with 3/4 inch female thread connection. Since there is also a screw connection on the side of the PE pipe, you can loosen the screw connection again if necessary and use it for further drip irrigation concepts.

• Connector for 20 mm PE hose on 1/2 " thread
• robust and reusable
• with 1/2 inch external thread

With this connection fitting you can connect a 20 mm PE pipe with a hose or pipe with 1/2 inch female thread connection. Since there is also a screw connection on the side of the PE pipe, you can loosen the screw connection again if necessary and use it for further drip irrigation concepts.

• to connect three PE hoses
• fast, simple assembly
• stable and tight fit

With the 90° T-fitting you can connect three 20 mm PE-pipes quickly and easily. The pipes cut to length are simply pushed onto the connector and the screw joint is tightened - that's it. This way you can easily branch the main line of your irrigation system and adapt it to your indoor grow.

• to connect three PE hoses
• fast, simple assembly
• stable and tight fit

With the 90° T-fitting you can connect two 20 mm PE-pipes with one 16 mm PE pipes quickly and easily. The pipes cut to length are simply pushed onto the connector and the screw joint is tightened - that's it. This way you can easily branch the main line of your irrigation system and adapt it to your indoor grow.

• to connect three PE hoses
• fast, simple assembly
• stable and tight fit

With the 90° T-fitting you can connect three 16 mm PE pipes quickly and easily. The pipes cut to length are simply pushed onto the connector and the screw joint is tightened - that's it. This way you can easily branch the main line of your irrigation system and adapt it to your indoor grow.

• tight fitting closure for PE hoses
• simple assembly
• reusable

Easy to install end plug for 16mm PE hose. To avoid loss of water and pressure, you should choose a permanently tight and firmly fitting plug. This end plug for 16 mm PE pipes is 100% tight when installed correctly and can be removed again if necessary and used for further grows.

• tight fitting closure for PE hoses
• simple assembly
• reusable

Easy to install end plug for 16mm PE hose. To avoid loss of water and pressure, you should choose a permanently tight and firmly fitting plug. This end plug for 20 mm PE pipes is 100% tight when installed correctly and can be removed again if necessary and used for further grows.

• for shutting off 16 mm PE hoses
• simple assembly
• applicable up to 4 bar

With this ball valve you can quickly and reliably close off parts of your irrigation system. The handle only needs to be turned by 90°. A ball with a hole inside will then prevent the flow. Ball valves are extremely robust and do not get clogged by lime or nutrients. Therefore they are particularly suitable for indoor and outdoor growing.

• for shutting off 20 mm PE hoses
• simple assembly
• applicable up to 4 bar

With this ball valve you can quickly and reliably close off parts of your irrigation system. The handle only needs to be turned by 90°. A ball with a hole inside will then prevent the flow. Ball valves are extremely robust and do not get clogged by lime or nutrients. Therefore they are particularly suitable for indoor and outdoor growing.

• Adapter and valve in one
• for shutting off a 16 mm drip tube

With a cylinder valve you can quickly close individual PE drip hoses of your irrigation system. If, for example, an area of your grow does not need water for a while, you have the possibility to temporarily remove it from the system. Ball valves are extremely robust and do not get clogged by lime or nutrients. Therefore they are especially suitable for indoor and outdoor growing. Your main line only needs a fitting with 1/2 inch internal thread at the end.

• Adapter and valve in one
• for shutting off a 16 mm drip tube

With a cylinder valve you can quickly close individual PE drip hoses of your irrigation system. If, for example, an area of your grow does not need water for a while, you have the possibility to temporarily remove it from the system. Ball valves are extremely robust and do not get clogged by lime or nutrients. Therefore they are especially suitable for indoor and outdoor growing. Your main line only needs a fitting with 3/4 inch internal thread at the end.

• Adapter and valve in one
• for shutting off a 20 mm drip tube

With a cylinder valve you can quickly close individual PE drip hoses of your irrigation system. If, for example, an area of your grow does not need water for a while, you have the possibility to temporarily remove it from the system. Ball valves are extremely robust and do not get clogged by lime or nutrients. Therefore they are especially suitable for indoor and outdoor growing. Your main line only needs a fitting with 3/4 inch internal thread at the end.

• with threaded flange on both sides
• for easy shut-off of 1/2" cables

With this ball valve you can quickly and reliably close off parts of your irrigation system. The handle only needs to be turned by 90°. A ball with a hole inside will then prevent the flow. Ball valves are extremely robust and do not get clogged by lime or nutrients. Therefore they are particularly suitable for indoor and outdoor growing.

• with threaded flange on both sides
• for easy shut-off of 3/4" cables

With this ball valve you can quickly and reliably close off parts of your irrigation system. The handle only needs to be turned by 90°. A ball with a hole inside will then prevent the flow. Ball valves are extremely robust and do not get clogged by lime or nutrients. Therefore they are particularly suitable for indoor and outdoor growing.

• Filter for drip irrigation
• prevents the dropper from clogging
• with threaded connection on both sides

A good filter is essential for your automatic drip irrigation system. It is essential that the water you irrigate your grow should be cleaned of even the smallest particles of dirt, otherwise the drippers and nozzles will clog too quickly. The plastic filter does this job excellently and with minimal maintenance. The filter element (plastic sieve) can be easily removed and cleaned.

• Filter for drip irrigation
• prevents the dropper from clogging
• with threaded connection on both sides

A good filter is essential for your automatic drip irrigation system. It is essential that the water you irrigate your grow should be cleaned of even the smallest particles of dirt, otherwise the drippers and nozzles will clog too quickly. The plastic filter does this job excellently and with minimal maintenance. The filter element (plastic sieve) can be easily removed and cleaned.

• connects hoses with 3/4 and 1/2 inch external thread
• robust and reusable

If you want to securely connect a 3/4 " hose in your irrigation system to a smaller ? " hose, you should use a sturdy connector. The reduction nipple has a hexagonal shape in the middle for a firm connection and can withstand pressures up to 10 bar.

• connects hoses with 1 and 1/2 inch external thread
• robust and reusable

If you want to securely connect a 1 " hose in your irrigation system to a smaller 1/2 " hose, you should use a sturdy connector. The reduction nipple has a hexagonal shape in the middle for a firm connection and can withstand pressures up to 10 bar.

• connects hoses with 1 and 3/4 inch external thread
• robust and reusable

If you want to securely connect a 1 " hose in your irrigation system to a smaller 3/4 " hose, you should use a sturdy connector. The reduction nipple has a hexagonal shape in the middle for a firm connection and can withstand pressures up to 10 bar.

• Connection for 5 mm drip tubes to 1/2"
• simple and dense solution
• Fits for 4x6mm micro tube

In case you want to connect 5 mm drip tubes to 1/2" tubes / hoses in your drip irrigation system, you can use this practical plug connector. Your pipe only needs a fitting with 1/2" external thread at the end. The connector also fits 4x6mm micro tubes. For easier assembly we recommend to hold the micro tube in hot water. This will make the hose more flexible and much easier to mount.

• Connection for 16 mm drip tubes to 1/2" external thread
• simple and dense solution
• for drip irrigation

In case you want to connect 16 mm drip tubes to 1/2" tubes / hoses in your drip irrigation system, you can use this practical plug connector. Your 1/2" pipe only needs a fitting with male thread at the end.

• Connection for 16 mm drip tubes to 3/4" external thread
• simple and dense solution
• for drip irrigation

In case you want to connect 16 mm drip tubes to 3/4" tubes / hoses in your drip irrigation system, you can use this practical plug connector. Your 3/4" pipe only needs a fitting with male thread at the end.

• Connection for 20 mm drip tubes to 3/4" external thread
• simple and dense solution
• for drip irrigation

In case you want to connect 20 mm drip tubes to 3/4" tubes / hoses in your drip irrigation system, you can use this practical plug connector. Your 3/4" pipe only needs a fitting with male thread at the end.

• robust
• flexible use

You can use pond liner in hydroponic systems or if you want to renew the bottom of your growbox. Due to its soft and tear-resistant nature, it is clearly superior to ordinary foils and tarpaulins. It also adapts quite well to square shapes and can therefore also be used to lay out the floor of fixed grow rooms.

• robust
• flexible use

You can use pond liner in hydroponic systems or if you want to renew the bottom of your growbox. Due to its soft and tear-resistant nature, it is clearly superior to ordinary foils and tarpaulins. It also adapts quite well to square shapes and can therefore also be used to lay out the floor of fixed grow rooms.

• Replacement membrane for Grow Max 3000
• easy to assemble

If the membranes of your Grow Max 3000 reverse osmosis unit have reached their wear limit, you can replace them easily and cheaply. The Grow Max 3000 l/h requires 2 membranes. The change is similar to the change of the pre-filter.

• replacement filter element
• easy to exchange
• against pollutants and very fine sediments

• powerful reverse osmosis filter
• removes 95 % of salts and heavy metals
• up to 3000 litres of pure water per day
• enables the exact setting of the EC value

The reverse osmosis unit Growmax Water 3000 is your strong partner for the production of pure irrigation water for hydro systems and the cultivation on all known media at indoor grows. The Growmax system works with a combination of filters and pressure and in this way eliminates almost all salts and heavy metals from tap water. The osmosis water filtered in this way not only protects the natural microorganisms in the soil. It also has an ideal pH value of 6.5 and a significantly reduced EC value of < 0.1. The nutrient uptake of the plants can therefore be controlled much better and more precisely.

45° Angled arrow dropper for use in drip irrigation.

Design: Black, for micropipe, 3 to 4 mm
Flow rate: 2,6 l/h
Length: 15,0 cm

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

• Fitting for use in micro irrigation
• angle for micro tube 4 x 6 mm (inner diameter 4 mm x outer diameter 6 mm)
• diameter 3,5 mm

Tip: Dip the micro tube briefly in hot water before connecting it. This makes the hose expandable and easier to install

• Fitting for use in micro irrigation
• end piece
• for micro tube 4 x 6 mm (inside-Ø x outside-Ø
• diameter 4 mm

With this plug you can either seal the ends of the pipes tightly or repair a small leak. To repair a hole that is too small, simply enlarge it with the 4 mm hole punch and close it with the plug.

• Fitting for use in micro irrigation
• needs 2.5 - 3 mm perforation in PE pipe
• for micro tube 4 x 6 mm

With this T-start connector you can lead two micro tubes from an opening in the supply line to your plants. For this purpose, a hole is punched in the PE line of your drip irrigation system with the hole punch and the start connector is simply inserted into the line with the corresponding nipple. Starting from the two hose nipples, you then lay the micro lines to your plants. For the precise supply of the individual plants you can use for your indoor grow then for example dripper.

• Fitting for use in micro irrigation
• T-connector for micro tube 4 x 6 mm (inner diameter 4 mm x outer diameter 6 mm)

The T-piece for the 4x6mm micro tube is suitable for branching off a branch for a dropper or another line from a micro tube line. The micro tube is simply pressed over the corresponding plug nipples.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

• free from cadmium and lead
• flexible PVC type 200
• Production with natural raw materials

This micro hose is manufactured under the highest standards of quality and freedom from pollutants. So you can use it without hesitation for the micro irrigation of your indoor or outdoor grow. Only natural raw materials are used in the production. Therefore, a contamination with heavy metals such as lead or cadmium can be excluded. Due to the flexibility of PVC you can lay this micro hose very easily.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

The next largest pump spray bottle we carry has a capacity of 5 litres. Like its little brother, this spray bottle allows you to add liquids in your desired mixing ratio, to spray onto the plant in a fine mist. 

As the name suggests, this is a pump spray bottle / pressure sprayer by Toolland. It has a capacity of 1.5 litres.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

• for use in Autopot or own tanks
• suitable for all 4x6mm micro tubes

To make a tight connection between the supply line of your Autopot easy2grow irrigation system and the water tank, simply insert this seal into a 10 mm pre drilled opening of the tank and then the 6 mm line into the seal.

• simple regulation of the flow rate
• for micro irrigation

With this micro-tap you can regulate the flow rate in parts of your drip irrigation system. For example, if you have used drippers without flow regulation for your Grow, you can place this tap directly in front of it in the line.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

• robust plastic
• for wall thicknesses up to 40 mm

If you need to connect a tank to your indoor grow, this fitting will serve you well. It is also suitable for tanks with thick materials, such as wooden barrels. Simply drill a 3/4 inch (a good 1.9 cm) hole into the tank and screw in the tank lead-through with the supplied seal. On the outside you can then mount a hose flange with a 3/4 inch female thread.

• for micro irrigation
• Supply 16 plants per connection point
• complete with holders, droppers and mounting ring

With the practical nozzle distributor you save time and work when setting up and operating your droplet irrigation system. Starting from only one point on the irrigation water supply line you can water four plants of your grow at the same time.

• for micro irrigation
• Supply 20 plants per connection point
• complete with holders, droppers and mounting ring

With the practical nozzle distributor you save time and work when setting up and operating your droplet irrigation system. Starting from only one point on the irrigation water supply line you can water four plants of your grow at the same time.

• for micro irrigation
• Supply 8 plants per connection point
• complete with holders, droppers and mounting ring

With the practical nozzle distributor you save time and work when setting up and operating your droplet irrigation system. Starting from only one point on the irrigation water supply line you can water four plants of your grow at the same time.

• for micro irrigation
• Supply 4 plants per connection point
• complete with holders, droppers and mounting ring

With the practical nozzle distributor you save time and work when setting up and operating your droplet irrigation system. Starting from only one point on the irrigation water supply line you can water four plants of your grow at the same time.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

• PE-hose in high quality
• LD-Polyethylene - light, with high stability
• resistant against many chemicals
• For the assembly of capillaries & micro tubes
• quantity in shopping cart = length in meters

You can use these PE pipes for your grow. No matter if indoor or outdoor, the used low density polyethylene (LDPE PN4) is very resistant against weather conditions and most of the chemicals used in cultivation. With diameters of 16 - 25 mm, PE hoses are perfect for main / supply lines for automatic drip irrigation. Due to the high quality of the material, it is also possible to install iDrop single drip irrigators or cappilaries directly on the hose.

• PE-hose in high quality
• LD-Polyethylene - light, with high stability
• resistant against many chemicals
• For the assembly of capillaries & micro tubes
• quantity in shopping cart = length in meters

You can use these PE pipes for your grow. No matter if indoor or outdoor, the used low density polyethylene (LDPE PN4) is very resistant against weather conditions and most of the chemicals used in cultivation. With diameters of 16 - 25 mm, PE hoses are perfect for main / supply lines for automatic drip irrigation. Due to the high quality of the material, it is also possible to install iDrop single drip irrigators or cappilaries directly on the hose.

• for use in Autopot- or own tanks
• suitable for 16 mm hoses

To create a tight connection between the supply line of your Autopot easy2grow irrigation system and the water tank, simply insert this seal into the corresponding opening of the tank and then the 16 mm line into the seal. If your tank does not have an opening, drill a 19 mm hole to insert the seal. The hole should be deburred.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

• 66 % larger than its predecessor
• also suitable for most bio-fertilizers
• further improved freedom from maintenance
• old systems can be extended with AQUAvalve5

Autopot has once again revised and further improved the proven Aquavalves. The 5 mm diameter inlet guarantees high flow rates and fastest filling. Even most biofertilizers with partially visible suspended particles can now be added. The risk of clogging has been further minimized. For your indoor grow this means: less maintenance, higher efficiency, greater reliability! If you still use an old Autopot with AQUAvalve irrigation system, you can easily combine or expand it with the new AQUAvalve5 valves.

• Easy to mount
• Protects lines and valves from contamination
• Easy to remove filter insert

With the 16 mm In-Line Filter from AutoPot, you can protect the irrigation system of your indoor grow from contamination without much effort. The in-line filter has screw caps on both ends, so you can easily remove the filter element.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

• For connecting 9 mm pipes
• 100 % tight
• easy handling
• reusable

With this T - connector you can connect three 9 mm lines of your AutoPot irrigation system and thus build, for example a branch.

• For connecting AQUAvalve5 to the distribution line

If you are working with 16 mm distribution lines and the new AQUAvalve5 in your irrigation system, you can branch off the 9 mm supply line to the plant pot with this T-connector.

• prevents the unwanted spreading of roots
• simple application
• suitable for 8,5L & 15L pots of the 1Pot- and easy2grow systems

With the AutoPot Root Control Sock you can prevent the roots of your plants from spreading uncontrolled from the pots into your grow system.

• keeps soil safely in the pot
• prevents contamination in the irrigation system
• suitable for 8,5 & 15L pots of the 1Pot- and easy2grow-System

To prevent soil from migrating from the pot into your irrigation system over time and possibly polluting the Aquavalves, place the AutoPot Matrix Disc in the bottom of the pot and then fill it with soil. While water can drain off easily, the soil is effectively prevented from being flushed out. Unrestrained root growth out of the pot is also reduced, but we recommend the Autopot Root Control Sock.

• easy mounting
• effective pre-filtering
• for mounting directly in the tank

The Autopot Golf filter is quick and easy to install. It is plugged onto the end of the hose of your irrigation system, which protrudes into the tank. The material of the filter stops coarse dirt and helps to keep your AQUAvalves functional.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

• for active root aeration
• enables increases in yield >/li>
• improves the absorption of nutrients

The Autopot AirDome gives you the ability to oxygenate the roots of each of your plants individually. Well aerated soils allow better root growth, prevent root rot and improve nutrient uptake. AutoPot promises significantly increased yields of up to 130% for indoor grow.

Square 15 liter replacement pot for AutoPot easy2grow and 1Pot modules.

• For the new AQUAvalve5 series
• higher flow rate than 6 mm

Whether you are replacing the old AQUAvalves or installing a completely new irrigation system, this hose will fit to connect AQUAvalve5 and the supply line. Price per running meter.

• functions simply and quickly
• seals securely
• reusable

To securely seal the 9mm lines of your AutoPot automatic irrigation system, simply use this end piece

• As a main or distribution line

AutoPot's 16 mm hose is suitable for use as the main or distribution line of your AutoPot irrigation system. The material can be easily shortened to the desired length. Price per running meter.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

• to be inserted into Autopot- or own tanks
• suitable for all 7x9mm micro tubes

To make a tight connection between the Autopot irrigation system and the water tank, simply insert this gasket into the opening of the tank and then insert the 9mm pipe into the gasket.
For your own tanks, a 12.5mm hole must be drilled in the tank

• For connecting 9 mm pipes
• reusable
• easy handling
• 100 % tight

With this cross connector you can connect four 9 mm lines of your AutoPot irrigation system. For example, if you need 2 branches from one main line, the cross connector is the perfect choice.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

• connects 16mm hoses with ClickFit connectors

With the ClickFit adaptor you can connect e.g. tanks with AutoPot ClickFit connection to a 16 mm pipe. The adaptor also fits the Gardena-System.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

• Hose connection on both sides
• For 9 mm hoses
• Extremely robust and reliable

With the ball valve from Autopot, you can safely shut off the corresponding line with a flick of the wrist. Inside the valve, a ball with a hole is rotated by 90° and thus closes the line. Ball valves are extremely reliable and usually do not clog even when organic fertilizers are used.

• Inline water tap for 16 mm pipes
• simple installation

You can install the AutoPot 16 mm faucet into a main line of your irrigation system in just a few simple steps.

• For connecting 16 mm pipes
• reusable
• easy handling
• 100 % tight

With this cross connector you can connect four 16 mm lines of your AutoPot irrigation system. For example, if you need 2 branches from one main line, the cross connector is the perfect choice.

• For connecting 16 mm pipes
• 100 % tight
• easy handling
• reusable

With this T - connector you can connect three 16 mm lines of your AutoPot irrigation system and thus build, for example, a branch.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.

This is a new addition to our grow shop. This text is a placeholder. You may already purchase the product.